1. Verizon Infrastructure
Equipment encased by wooden fence, with limbs touching. HIGHLY recommend cutting back limbs so they do not touch the wooden structure.1. Limb
Limb up to 4 ft. off the ground and check for surrounding branches.3. Limb and prune
Evaluate further with arborist.4. Create fuel break
Recommend leaving habitat trees and area. However, highly recommend reducing the surrounding fuel load (considering small fire break), and remove any dead and down limbs on the ground. Protect habitat and try to prevent from igniting by reducing fuel loads around it. Will create a fuel break where grass is reduced 2-3 inches up to 15 ft away from the trees. The remaining grass can be cut 6-8 inches.3. Reduce grass
High priority for grazing. Reducing the grass fuel load around the habitat trees can help reduce the amount of work needed in habitat. For the general area, I would recommend either cleaning up the understory around the habitat trees, including limbing and pruning; or reduce the grass. Both would be best, but the tall grass would make it easy for fire to carry through this site.4. Dead cottonwood across riparian
Down tree, across riparian, very large tree. Will be difficult, technically, to remove. Recommend FAL 1.3. Wooden Fence
Remove wooden fence2. Limb and clear understory
Snag within cluster. Limb area and clear understory2. Hazard Tree
Recommend removing3. Reduce grass
High priority for grazing3. Hazard tree
Showing signs of hallowing out, could fall. Not leaning towards the trail, but it is surrounded by grass and could easily ignite. Would recommend removing.1. Utility Equipment
Highly recommend limbing back so it doesn't touch equipment4. Dead cottonwood across riparian
Down tree, across riparian, very large tree. Will be difficult, technically, to remove. Recommend FAL 1.3. Potential Hazard Tree - Angle 2
1. Crown entangled
Remove the limbs that are almost touching to prevent fire spreading through the crown.1. Hazard Tree
Hazard tree leaning towards highly-trafficked sidewalk. Would recommend removing. Less than 18 ft. and no more than 12 in. in diameter.2. Limbs on ground
Limbs on ground from prior project4. Create fuel/fire break
Keep habitat tree, but create a fuel break around it. Cut grass 2-3 inches down at a minimum distance of 15 ft. around the tree. Cut surrounding grass down 6-8 inches.2. Slash on ground
Slash on ground from prior mitigation efforts. Also recommend limbing2. Dead and down
Consider removing1. VI - East
Equipment encased by wooden fence, with limbs touching. HIGHLY recommend cutting back limbs so they do not touch the wooden structure.1. Slash on ground
Slash on ground from prior mitigation3. Avian Nest Observed
Avian nest observed in habitat trees. Reduce fuel load a minimum of 15 ft. around the tree. Cut grass 2-3 inches.2. Prune and limb
Prune and limb for tree health2. Dead and down
Recommend removing2. Active Avian Nest
1. Crown entanglement
Limb so branches are not so close together.2. Limb
Limb dead branches4. Remove rope swing
Rope swing attached to questionable tree. Highly recommend removing. Coordinates: 39.93157, -105.150162. Dead and down
Recommend removing2. Dead and down
Consider removing1. Light Limbing
Light limbing3. See recommendations
1. Remove wooden fence. / 2. Reduce fuel load around the patch. / 3. Remove some of the dead and down1. Limb
Limb away from the fence because of the grass model to the south.1. Slash on ground/Limb
Slash on ground/ Limbing up to 4 ft. and so branches don't touch3. Hazard Tree
Recommend removing2. Dead and down
From other side of Rock Creek3. Remove large snag - high priority
Coordinates: 39.93068, -105.15583 / Technical3. Limb
Limb up to 4 ft. off the ground and make sure branches are not touching.1. Slash on ground/ limb
Slash on ground/ Limb up to 4 ft. and so branches don't touch3. Limb and clear understory
Cottonwoods mainly, so limb dead branches. Try to reduce fuel load, carefully. Reduce grass load surrounding habitat area.3. Remove large snag - high priority
Coordinates: 39.93068, -105.15583 / Technical1. Burned Tree
Wide lens2. Slash on ground
Slash on ground from prior mitigation efforts. Also recommend limbing1. Dripline
Limbing up to 4 ft. and so branches don't touch1. Dripline
Limb up to 4 ft. off the grown and so branches aren't touching.4. Remove rope swing
3. Reduce grass
High priority grazing area, mowing grass to 4-6 in.4. Dead cottonwood across riparian
Down tree, across riparian, very large tree. Will be difficult, technically, to remove. Recommend FAL 1. Coordinates: 39.93170, -105.152032. Clear the understory
Slash on the ground, clear understory3. Hazard tree
Showing signs of hallowing out, could fall. Not leaning towards the trail, but it is surrounded by grass and could easily ignite. Would recommend removing. Coordinates: 39.93081, -105.154903. Dead and down
Remove dead and down1. Burned Tree
Closer1. Limb
Limb up to 4 ft. off the ground and check for surrounding branches.4. Remove dead tree - high priority
Dead, burned… no apparent habitat, leaning towards small trail - above 18 ft. Coordinates: 39.93170, -105.152662. Limb and clear understory
Limb dead branches and clear understory1. Dripline
Limbing so branches don't touch2. Remove snag and limb
Remove snag and limb3. Limb
Limb dead branches and consider clearing understory Coordinates: 39.93084, -105.155803. Reduce grass
High priority grazing, mowing 4-6 in3. Potential hazard tree
Evaluate further with arborist.3. Reduce grass
Reducing the grass fuel load around the habitat trees can help reduce the amount of work needed in habitat. For the general area, I would recommend either cleaning up the understory around the habitat trees, including limbing and pruning; or reduce the grass. Both would be best, but the tall grass would make it easy for fire to carry through this site.